j9九游会登录入口--值得信赖

您地点的地位:首页 > 新闻中心 > 行业静态 > 注释
 新闻中心
更多>>联系j9九游会
东莞仁兴优创实业有限公司
联 系  人:   胡老师
###822
              82031698
挪动>###
###529
E-mail:>###
>###4号
 行业静态

ABS通明管的电学功能及加工功能

作者:办理员 泉源: >###9:53 人气:30 批评:0 标签:
ABS通明管的电学功能及加工功能
电学功能
  ABS的电绝缘性较好,而且简直不受温度、湿度和频率的影响,可在大少数情况下利用。
情况功能
  ABS不受水、无机盐、碱及多种酸的影响,但可溶于酮类、醛类及氯代烃中,受冰乙酸、动物油等腐蚀会发生应力开裂。ABS的耐候性差,在紫外光的作用下易发生降解;于户外半年后,打击强度降落一半。
ABS electrical properties and processing properties of transparent tubes 
Electrical Properties 
ABS electrical insulation is better, and almost independent of temperature, humidity and frequency, can be used in most environments. 
Environmental performance 
ABS from water, inorganic salts, alkalis and a variety of effects of acid, but soluble in ketones, aldehydes, and chlorinated hydrocarbons by glacial acetic acid, vegetable oil will produce stress corrosion cracking. ABS poor weather, under the action of ultraviolet light easy to produce degradation; outdoor six months, the impact strength decreased by half.
ABS塑料的加工功能
  ABS同PS一样是一种加工功能优秀的热塑性塑料,可用通用的加工办法加工。   ABS的熔体活动性比PVC和PC好,但比PE、PA及PS差,与POM和HIPS相似;ABS的活动特征属非牛顿流体;其熔体粘度与加工温度和剪切速率都有干系,但对剪切速率更为敏感。   ABS的热波动性好,不易呈现降解征象。ABS的吸水率较高,加工前应举行枯燥处置。一样平常成品的枯燥条件为温度80~85℃,工夫2~4h;对特别要求的成品(如电镀)的枯燥条件为温度70~80℃,工夫18~18h。ABS成品在加工中易发生内应力,内应力的巨细可经过浸入冰乙酸中查验;如应力太大和成品对应力开裂相对克制,应举行退火处置,详细条件为放于70~80℃的热风循环枯燥箱内2~4h,再冷却至室温即可。
ABS plastics processing performance 
ABS with PS is an excellent processability as thermoplastics, common processing methods can be processed. ABS melt flow ratio of PVC and PC good, but worse than PE, PA and PS, similar to the POM and HIPS; flow characteristics of the ABS is a non-Newtonian fluid; melt viscosity and processing temperature and shear rate have a relationship However, more sensitive to shear rate. ABS good thermal stability, and less prone to degradation phenomena. ABS high water absorption, should be dried before processing. General products, dry conditions for temperature 80 ~ 85 ℃, time 2 ~ 4h; special requirements of products (such as electroplating) drying conditions for temperature 70 ~ 80 ℃, time 18 ~ 18h. ABS products easy to produce in the processing of internal stress, the size of the internal stress can be immersed in glacial acetic acid test; such as stress too much stress cracking and articles for absolute prohibition, should be annealed, the specific conditions placed on the hot air circulation for 70 ~ 80 ℃ of the oven 2 ~ 4h, then cooled to room temperature.
本文网址:/show.asp?id=96
更多>>新闻批评
宣布批评